1. introduction gps click is an accessory board in mikrobus? form factor. its a compact solution for adding gps functionality to your device. it features LEA-6S, high performance u-blox 6 positioning engine. board can be interfaced with a microcontroller through uart or i 2 c connection, or data can be acquired using pc application through usb connection. board features connector compatible with active and passive antennas. it can operate on 3.3v power supply only. once you have soldered the headers your board is ready to be placed into desired mikrobus? socket. make sure to align the cut in the lower-right part of the board with the markings on the silkscreen at the mikrobus? socket. if all the pins are aligned correctly, push the board all the way into the socket. 3. plugging the board in 2 3 2. soldering the headers 1 4. features and applications gps click board with its LEA-6S module features acquisition down to 1s, C147dbm coldstart sensitivity and 5hz update rate. you can achive low power consumption due to intelligent, user confgurable power management. mentioned features make this board ideal for asset tracking, road navigation devices, public transportation vehicle infor mation systems and more. turn the board upward again. make sure to align the headers so that they are perpendicular to the board, then solder the pins carefully. turn the board upside down, so that bottom side is facing you upwards. place shorter parts of the header pins in the both soldering pad locations. gps click before using your click board, make sure to solder the provided 1x8 male headers to both sides of the board. two 1x8 male headers are included with the board in the package. click board www.mikroe.com gps click manual ver. 1.00
8. support mikroelektronika ofers free tech support (www.mikroe.com/esupport) until the end of product lifetime, so if something goes wrong, we are ready and willing to help! 7. code examples .com once you have done all the necessary preparations, its time to get your click board up and running. we have provided the examples for mikroc, mikrobasic and mikropascal compilers on our libstock website. just download them and you are ready to start. 5. gps click board schematics us b _ d p usb_d m sd a 2 s cl 2 txd 1 rxd1 sd a 2 s cl2 txd 1 rxd1 timepulse device/otg connector 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 sd a 2 s cl 2 tx d 1 rx d 1 rf _i n gn d n c vc c gn d vcc_out c fg _com1 rese t v _b c k p r eserved gn d gn d gn d vcc_r f v_ an t aaden t0_ n n c timepulse n c n c v ddus b usb_d m us b _ d p e x tint 0 gps 1 lea6s vc c an rs t cs sck mosi miso +3.3v gn d pwm in t r x t x sc l sd a +5 v gn d reset_n r 7 1 0 vcc_r f vc c c2 100n f r 3 22 0 time pulse led timepulse rf _i n c1 2.2u f c3 2 . 2 u f 1 2 3 i n gn d ou t 5 4 en ad j reg1 ap7331-adj r 6 180 k r 2 300 k r 1 1k 1 2 3 4 5 gn d i d d + d - vbus c n 3 u sb mi nib r 5 22 0 power led usb_d m us b _ d p d 1 b at4 3 vc c vdd_us b vdd_us b c n 4 a ntenn a reset_n mikroelektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document. specifcation and information contained in the present schematic are subject to change at any time without notice. copyright ? 2012 mikroelektronika. all rights reserved. 6. power supply - 3.3v only board is designed to use 3.3v power supply only. if you need to add gps feature to your 5v prototype or development board, we recommend you to use other boards such as the smartgps accessory board: http://www.mikroe.com/eng/products/ view/122/smartgps-board/
|
